| Name | Type | Description |
|---|
| IsSelectable |
P_SINGLEVALUE
/
IfcBoolean
|
 | Is Selectable | Indication whether the S-function can be switched off or not. |
 | 切り替え | 装置の “ON-OFF”状態を電気的表示が切り替え可能かどうか。 |
|
| NominalCurrentAdjusted |
P_SINGLEVALUE
/
IfcBoolean
|
| Nominal Current Adjusted | An indication if the tripping currents of the short time protection is related to the nominal current multiplied with the actual setting of the current adjustment, if any, of the long time protection part of the protective device, or not. |
| 定格調整電流 | 電流によって、動作時間が短かかったり長かったりするかどうか。 |
|
| ReleaseCurrent |
P_SINGLEVALUE
/
IfcElectricCurrentMeasure
|
| Release Current | The release current in [x In] for the initial tripping of the S-function. |
| 放出電流 | 放出する電流は、S-functionの初期特性。 |
|
| ReleaseTime |
P_SINGLEVALUE
/
IfcTimeMeasure
|
| Release Time | The release time in [s] for the initial tripping of the relevant part. This time indicates that for current lower than the indicated release current, the tripping time will be longer than the indicated release time. The value is given as a mean value. |
| 放出時間 | 関連する部分の初期トリップのための[s]が放出時間。
このトリップ時間は、リリースの電流よりも低い電流の場合、指定された動作時間よりも長くなります。
値が平均値として与えられる。 |
|
| CurrentTolerance1 |
P_SINGLEVALUE
/
IfcPositiveRatioMeasure
|
| Current Tolerance1 | The tolerance for the current of time/current-curve in [%]. |
| 許容電流1 | 時間/特性曲線の許容範囲を[％]で指定。 |
|
| CurrentToleranceLimit1 |
P_SINGLEVALUE
/
IfcTimeMeasure
|
| Current Tolerance Limit1 | The time limit in [s] limiting the application of CurrentTolerance1, if any. If the value is set to 0, the value of the CurrentTolerance1 is valid for the whole time/current-curve. |
| 許容電流限界1 | 許容電流1を制限する時間制限。
値が0の場合は、制限はない。 |
|
| CurrentTolerance2 |
P_SINGLEVALUE
/
IfcPositiveRatioMeasure
|
| Current Tolerance2 | The tolerance for the current of time/current-curve in [%] valid for times above CurrentTolereanceLimit1. |
| 許容電流2 | [％]で指定された時間/特性曲線の許容範囲は、上記の許容電流限界1の時間で有効です。 |
|
| IsCurrentTolerancePositiveOnly |
P_SINGLEVALUE
/
IfcBoolean
|
| Is Current Tolerance Positive Only | Indication whether the value of CurrentTolerance1 is provided as a positive tolereance only or not. If not, the value is proved as a pluss/minus tolerance. |
| 電流許容値 | 許容電流限界1の値のみかどうか
上記でない場合、電流許容値はプラス/マイナスした値。 |
|
| TimeTolerance1 |
P_SINGLEVALUE
/
IfcPositiveRatioMeasure
|
| Time Tolerance1 | The tolerance for the time of time/current-curve in [%]. |
| 許容時間1 | [％]で時間/特性曲線の許容時間を設定 |
|
| TimeToleranceLimit1 |
P_SINGLEVALUE
/
IfcElectricCurrentMeasure
|
| Time Tolerance Limit1 | The current limit in [x In] limiting the application of TimeTolerance1, if any. If the value is set to 0, the value of the TimeTolerance1 is valid for the whole time/current-curve. |
| 許容限界時間1 | 許容時間1を制限する電流制限値。
値が0の場合は、制限はない。 |
|
| TimeTolerance2 |
P_SINGLEVALUE
/
IfcPositiveRatioMeasure
|
| Time Tolerance2 | The tolerance for the time of the time/current-curve in [%] valid for currents above TimeToleranceLimit1. |
| 許容時間2 | [％]で指定された時間/特性曲線の許容範囲は、上記の許容電流限界1の電流で有効です。 |
|
| IsTimeTolerancePositiveOnly |
P_SINGLEVALUE
/
IfcBoolean
|
| Is Time Tolerance Positive Only | Indication whether the value of TimeTolerance1 is provided as a positive tolereance only or not. If not, the value is proved as a pluss/minus tolerance. |
| 時間許容値 | 許容時間1の値のみかどうか。
上記でない場合、時間許容値は、プラス/マイナスした値。 |
|
| ReleaseCurrentI2tStart |
P_SINGLEVALUE
/
IfcElectricCurrentMeasure
|
| Release Current I2t Start | The release current in [x In] for the start point of the I2t tripping curve of the S-function, if any. |
| I2tの開始放流電流 | S関数の特性曲線I2tの始点[x In]が開始放流電流。 |
|
| ReleaseTimeI2tStart |
P_SINGLEVALUE
/
IfcTimeMeasure
|
| Release Time I2t Start | The release time in [s] for the start point of the I2t tripping curve of the S-function, if any |
| I2tの開始放流時間 | S関数の特性曲線I2tの始点[s]が開始放流時間。 |
|
| ReleaseCurrentI2tEnd |
P_SINGLEVALUE
/
IfcElectricCurrentMeasure
|
| Release Current I2t End | The release current in [x In] for the end point of the I2t tripping curve of the S-function, if any. The value of ReleaseCurrentI2tEnd shall be larger than ReleaseCurrentI2tStart. |
| I2tの終了放流電流 | S関数のI2の特性曲線のエンドポイントの[s]を放流電流。
I2tの終了放流電流がI2tの開始放流電流よりも低くしなければならない。 |
|
| ReleaseTimeI2tEnd |
P_SINGLEVALUE
/
IfcTimeMeasure
|
| Release Time I2t End | The release time in [s] for the end point of the I2 tripping curve of the S-function, if any. The value of ReleaseTimeI2tEnd shall be lower than ReleaseTimeI2tStart. |
| I2tの終了放流時間 | S関数のI2の特性曲線のエンドポイントの[s]を放流時間。
I2tの終了放流電流時間がI2tの開始放流時間よりも低くしなければならない。 |
|
| IsOffWhenLfunctionOn |
P_SINGLEVALUE
/
IfcBoolean
|
| Is Off When Lfunction On | Indication whether the S-function is automatically switched off when the I-function is switched on. |
|
buildingSMART Data Dictionary
PSD-XML
Link to this page