IfcDoorTypeOperationEnum

Item	SPF	XML	Change	Description
4.0.0.0
IfcDoorTypeOperationEnum			ADDED

Semantic definitions at the type

Type definition

This enumeration defines the basic ways to describe how doors operate, as shown in Figure 189. It combines the partitioning of the door into a single or multiple door panels and the operation types of that panels.

In the most common case of swinging doors the IfcDoorTypeOperationEnum defined the hinge side (left hing or right hung) and the opening direction (opening to the left, opening to the right). Whether the door opens inwards or outwards is determined by the local coordinate system of the IfcDoor, or IfcDoorStandardCase.

NOTE There are different definitions in various countries on what a left opening or left hung or left swing door is (same for right). Therefore the IFC definition terms may derivate from the local standard and may need to be mapped appropriately.

HISTORY New Enumeration in IFC4.

IFC4 CHANGE The new IfcDoorTypeOperationEnum replaces the use of IfcDoorStyleOperationEnum that is deprecated from IFC4 onwards.

Enumerator	Description	Figures
SINGLE_SWING_LEFT	Door with one panel that opens (swings) to the left. The hinges are on the left side as viewed in the direction of the positive y-axis. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
SINGLE_SWING_RIGHT	Door with one panel that opens (swings) to the right. The hinges are on the right side as viewed in the direction of the positive y-axis. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
DOUBLE_DOOR_ SINGLE_SWING	Door with two panels, one opens (swings) to the left the other opens (swings) to the right. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
DOUBLE_SWING_LEFT	Door with one panel that swings in both directions and to the left in the main trafic direction. Also called double acting door. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
DOUBLE_SWING_RIGHT	Door with one panel that swings in both directions and to the right in the main trafic direction. Also called double acting door. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
DOUBLE_DOOR_ DOUBLE_SWING	Door with two panels, one swings in both directions and to the right in the main trafic direction the other swings also in both directions and to the left in the main trafic direction. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
DOUBLE_DOOR_ SINGLE_SWING_ OPPOSITE_LEFT	Door with two panels that both open to the left, one panel swings in one direction and the other panel swings in the opposite direction. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
DOUBLE_DOOR_ SINGLE_SWING_ OPPOSITE_RIGHT	Door with two panels that both open to the right, one panel swings in one direction and the other panel swings in the opposite direction. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
SLIDING_TO_LEFT	Door with one panel that is sliding to the left.
SLIDING_TO_RIGHT	Door with one panel that is sliding to the right.
DOUBLE_DOOR_SLIDING	Door with two panels, one is sliding to the left the other is sliding to the right.
FOLDING_TO_LEFT	Door with one panel that is folding to the left.
FOLDING_TO_RIGHT	Door with one panel that is folding to the right.
DOUBLE_DOOR_FOLDING	Door with two panels, one is folding to the left the other is folding to the right.
REVOLVING	An entrance door consisting of four leaves set in a form of a cross and revolving around a central vertical axis (the four panels are described by a single IfcDoor panel property).
ROLLINGUP	Door that opens by rolling up. NOTE Whether it rolls up to the inside or outside is determined at the IfcDoor.
SWING_FIXED_LEFT	Door with one panel that opens (swings) to the left and one fixed panel. The hinges of the swinging panel are on the left side as viewed in the direction of the positive y-axis. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
SWING_FIXED_RIGHT	Door with one panel that opens (swings) to the right and one fixed panel. The hinges of the swinging panel are on the right side as viewed in the direction of the positive y-axis. NOTE Direction of swing (whether in or out) is determined at the IfcDoor or IfcDoorStandardCase.
USERDEFINED	User defined operation type
NOTDEFINED	A door with a not defined operation type is considered as a door with a lining, but no panels. It is thereby always open.

Figure 189 — Door operations

NOTE

Figures are shown in the ground view.
Figures (symbolic representation) depend on the national building code.
These figures are only shown as illustrations, the actual representation in the ground view might differ.
Open to the outside is declared as open into the direction of the positive y-axis, determined by the ObjectPlacement at IfcDoor
The location of the panel relative to the wall thickness is defined by the ObjectPlacement at IfcDoor, and the IfcDoorLiningProperties.LiningOffset parameter.

Enumeration definition

Constant	Description
SINGLE_SWING_LEFT	Door with one panel that opens (swings) to the left. The hinges are on the left side as viewed in the direction of the positive y-axis.
SINGLE_SWING_RIGHT	Door with one panel that opens (swings) to the right. The hinges are on the right side as viewed in the direction of the positive y-axis.
DOUBLE_DOOR_SINGLE_SWING	Door with two panels, one opens (swings) to the left the other opens (swings) to the right.
DOUBLE_DOOR_SINGLE_SWING_OPPOSITE_LEFT	Door with two panels that both open to the left, one panel swings in one direction and the other panel swings in the opposite direction.
DOUBLE_DOOR_SINGLE_SWING_OPPOSITE_RIGHT	Door with two panels that both open to the right, one panel swings in one direction and the other panel swings in the opposite direction.
DOUBLE_SWING_LEFT	Door with one panel that swings in both directions and to the left in the main trafic direction. Also called double acting door.
DOUBLE_SWING_RIGHT	Door with one panel that swings in both directions and to the right in the main trafic direction. Also called double acting door.
DOUBLE_DOOR_DOUBLE_SWING	Door with two panels, one swings in both directions and to the right in the main trafic direction the other swings also in both directions and to the left in the main trafic direction.
SLIDING_TO_LEFT	Door with one panel that is sliding to the left.
SLIDING_TO_RIGHT	Door with one panel that is sliding to the right.
DOUBLE_DOOR_SLIDING	Door with two panels, one is sliding to the left the other is sliding to the right.
FOLDING_TO_LEFT	Door with one panel that is folding to the left.
FOLDING_TO_RIGHT	Door with one panel that is folding to the right.
DOUBLE_DOOR_FOLDING	Door with two panels, one is folding to the left the other is folding to the right.
REVOLVING	An entrance door consisting of four leaves set in a form of a cross and revolving around a central vertical axis (the four panels are described by a single IfcDoor panel property).
ROLLINGUP	Door that opens by rolling up.
SWING_FIXED_LEFT	Door with one panel that opens (swings) to the left and one fixed panel. The hinges of the swinging panel are on the left side as viewed in the direction of the positive y-axis.
SWING_FIXED_RIGHT	Door with one panel that opens (swings) to the right and one fixed panel. The hinges of the swinging panel are on the right side as viewed in the direction of the positive y-axis.
USERDEFINED	User defined operation type.
NOTDEFINED	A door with a not defined operation type is considered as a door with a lining, but no panels. It is thereby always open.

Formal representations

XML Specification

 <xs:simpleType name="IfcDoorTypeOperationEnum">

  <xs:restriction base="xs:string">

   <xs:enumeration value="single_swing_left"/>

   <xs:enumeration value="single_swing_right"/>

   <xs:enumeration value="double_door_single_swing"/>

   <xs:enumeration value="double_door_single_swing_opposite_left"/>

   <xs:enumeration value="double_door_single_swing_opposite_right"/>

   <xs:enumeration value="double_swing_left"/>

   <xs:enumeration value="double_swing_right"/>

   <xs:enumeration value="double_door_double_swing"/>

   <xs:enumeration value="sliding_to_left"/>

   <xs:enumeration value="sliding_to_right"/>

   <xs:enumeration value="double_door_sliding"/>

   <xs:enumeration value="folding_to_left"/>

   <xs:enumeration value="folding_to_right"/>

   <xs:enumeration value="double_door_folding"/>

   <xs:enumeration value="revolving"/>

   <xs:enumeration value="rollingup"/>

   <xs:enumeration value="swing_fixed_left"/>

   <xs:enumeration value="swing_fixed_right"/>

   <xs:enumeration value="userdefined"/>

   <xs:enumeration value="notdefined"/>

  </xs:restriction>

 </xs:simpleType>

EXPRESS Specification


TYPE IfcDoorTypeOperationEnum = ENUMERATION OF (

 SINGLE_SWING_LEFT, 
 SINGLE_SWING_RIGHT, 
 DOUBLE_DOOR_SINGLE_SWING, 
 DOUBLE_DOOR_SINGLE_SWING_OPPOSITE_LEFT, 
 DOUBLE_DOOR_SINGLE_SWING_OPPOSITE_RIGHT, 
 DOUBLE_SWING_LEFT, 
 DOUBLE_SWING_RIGHT, 
 DOUBLE_DOOR_DOUBLE_SWING, 
 SLIDING_TO_LEFT, 
 SLIDING_TO_RIGHT, 
 DOUBLE_DOOR_SLIDING, 
 FOLDING_TO_LEFT, 
 FOLDING_TO_RIGHT, 
 DOUBLE_DOOR_FOLDING, 
 REVOLVING, 
 ROLLINGUP, 
 SWING_FIXED_LEFT, 
 SWING_FIXED_RIGHT, 
 USERDEFINED, 
 NOTDEFINED);
END_TYPE;


 EXPRESS-G diagram